I Bar Grating Specification

services; fabrication; fabricating; marco fabI Bar Grating Specification

I Bar Grating Specification

Bar Depth 1.25" Open Area 40%: Max Width 5' Load Bar Centers 1" Approximate Weight 3.77 lbs/ft 2 Cross Bar Spacing 6" Engineering Properties Per Foot of Width: A = 4.13 in 2 I = 0.83 in 4 S = 1.33 in 3 : Hold Down Clip: T or W

Carbon Steel Heavy Duty Bar Grating is usually provided with bare steel (no finish), painted with one coat of IG EcoCoat™, or hot dip galvanized in accordance with ASTM A-123. Due to discolorization that occurs during welding and fabrication, Stainless Steel Heavy Duty Bar Grating typically require secondary cleaning.;bearing bar) of the Bar Grating item. Product Spacing (e.g. 19-W-4) refers to the industry specification for Bar Grating products. For example, the first number refers to the bearing bar spacing measured on center (19 = 19/16" or 1-3/16"), the letter refers to the construction type (W = welded) and the last number references the cross bar ;Bar grating may be fabricated to your specifications. 713.672.7595. 713.672.0653 fax 865 Lockwood Drive Houston, Texas 77020;Specifications of steel grating for stair treads. Steel grating type: welded steel grating and press bar grating. Bearing bar type: flat bar and I bar. Bearing bar pitch: 20 mm, 30 mm or 40 mm. Cross bar pitch: 50 mm or 100 mm. Nosing type: checker plate, strip plate and hole plate. Surface treatment: galvanized or anti-corrosion painted.;Metal Bar Grating Manual 531-17. 2017; Download PDF. Technical data, specifications, and recommended practices applicable to steel, stainless steel and aluminum gratings; includes photographs, load tables and details of typical installations.;Full-locked steel bar grating The bearing bars and cross bars are notched and have the same height. Heavy-duty pressed bar grating The bearing bars are higher than the cross bars and they are all notched. Press-locked bar grating Only the bearing bars are notched, the cross bars are common plain steel. And they have different height. Louver bar

Pressure Locked Bar Grating for Architectural Ceiling Panels

Pressure Locked Bar Grating for Architectural Ceiling Panels

Pressure Locked Metal Bar Grating is a system constructed of interlocking slotted bars bonded together using tremendous hydraulic pressue. The bars are positioned every 2 inch or 4 inch. Also known as press-locked bar grates. Permanent locking is achieved by forcing the deep cross bar into the bearing bar. Both the cross bars and the bearing ;Bar Grating Specifications. A proper design for bar gratings includes a determination of material, construction, loading conditions, unsupported clear span, surface treatment, finish, and edge banding. Carefully considering the application and environment will allow the sales staff at Peterson Company to help you select the products that will ;Specifications, Types and Requirements for Metal Open Bar Grating. Metal open bar grating, also called steel grating, steel bar grating, is a type of solid grating widely used in the industrial applications as flooring and stair treads. It has anti-corrosion material, multi-type and anti-slip surface to help secure workers safe and reduce ;Bar Depth 1.25" Open Area 40%: Max Width 5' Load Bar Centers 1" Approximate Weight 3.77 lbs/ft 2 Cross Bar Spacing 6" Engineering Properties Per Foot of Width: A = 4.13 in 2 I = 0.83 in 4 S = 1.33 in 3 : Hold Down Clip: T or W;Bar Grating Specification Sheets At Nucor Grating, it is important to us that we supply engineers and architects with as much information as possible to ensure a successful project. Spec sheets are designed to assist engineer and architects in project scoping in an effort to utilize optimal products and maximize efficiency throughout the project.;The overall dimension of a flooring panel measured at right angles to the load bearing bars. This dimension is always referred to as “”width””, even if it exceeds the length. (Standard widths are multiples of BearingBar Centres plus Bearing Bar Width).;installing steel bar grating at the locations shown on the plans or as directed by the Engineer. Construction of the steel bar grating shall be done in accordance with this specification, the plans, and the manufacturer’s instructions. 2. REFERENCES: American National Standards Institute (ANSI) MBG 531-09 Metal Bar Grating Manual

Grating | Peterson Company

Grating | Peterson Company

Bar Grating Specifications. A proper design for bar gratings includes a determination of material, construction, loading conditions, unsupported clear span, surface treatment, finish, and edge banding. Carefully considering the application and environment will allow the sales staff at Peterson Company to help you select the products that will ;/For serrated grating, the depth of grating required for a specied load is 1/4” greater than in the chart. U= Uniform load, Psf C= Concentrated load at (mid-span), LB per foot of grating width In order to obtain the permissible loading capacity for each type of grating, multiply its assigned value times the value on the table. 22W4 Y 22W2 0.85;Bar Grating Specification List . I. Bearing Bar (Load Bar) can be two types: plain flat type and serrated type. So, please mention the bar type with your inquiry. Common bar size range(mm): 20 x 3 to 100 x 9. II. Bearing Bar Pitch / Spacing (center to center): 12.5 to 100 mm normally. 30, 40, 60mm are recommended. American standard size is ;Product Spacing (e.g. 19-W-4) refers to the industry specification for Bar Grating products. For example, the first number refers to the bearing bar spacing measured on center (19 = 19/16" or 1-3/16"), the letter refers to the construction type (W = welded), and the last number references the cross bar spacing measured on center (4 = 4").;Bar grating is ideal for industrial steel grating flooring and metal grates. Direct Metals offers plain or serrated bar grating surfaces in galvanized, bare steel, or painted finishes. Welded bar grating is the most common type of bar grating. Welded steel grating is joined at the intersection of the bearing bars and cross bars.;Carbon Steel Heavy Duty Bar Grating is usually provided with bare steel (no finish), painted with one coat of IG EcoCoat™, or hot dip galvanized in accordance with ASTM A-123. Due to discolorization that occurs during welding and fabrication, Stainless Steel Heavy Duty Bar Grating typically require secondary cleaning.;Our standard grating is ISO-Polyester, which provides superior performance in corrosive environments. Call for Pricing on the following FRP Bar Grating Profiles. I-6000 , I-6010, I-6015 I-4000, I-4010, I-4015 T-1800, T-1810, T-1815 T-5000, T-5020. Pultruded Fiberglass Grating Specifications

1 1/4" Deep / 40% Open FRP Grating | I

1 1/4" Deep / 40% Open FRP Grating | I

Bar Depth 1.25" Open Area 40%: Max Width 5' Load Bar Centers 1" Approximate Weight 3.77 lbs/ft 2 Cross Bar Spacing 6" Engineering Properties Per Foot of Width: A = 4.13 in 2 I = 0.83 in 4 S = 1.33 in 3 : Hold Down Clip: T or W

Contact Us to Learn More About Your Perforated Metal Product Options

Feel free to contact Royce Specialty Steel to learn more about how our stock and custom perforated metal product offerings can benefit your industrial operation, and please let us know about any specific customization requirements or special requests. We’ll also be happy to provide a no-obligation quote and help with your ordering process. If you need assistance calculating the open area, contact one of our friendly representative and we’d be happy to assist you.

At Royce Specialty Steel, we’re all about three things: Quality, Speed and Reliability.